Videx 1000 Code, 2 Relay, Standalone/Networkable Codelock (Matt 316)

Videx 4902/M 1000 Code, 2 Relay, Modular 4000 Series Standalone or Networkable (RS485) Codelock Module with Blue Backlit Key Buttons (Matt 316 Stainless Steel Finish)

The Videx 4902/M 4000 series codelock module with blue backlit buttons can operate as a standalone codelock or be networked via an RS485 bus (it can be networked with other 4902 codelocks only).

This codelock has 2 relays and allows for up to 1000 codes that can be assigned to one or both of the relays.

This keypad has dry relay contacts (CO, NO and NC) where each output can be programmed from 1-255 seconds or set to 00 for latching. It also features two switched 0V push to exit inputs to activate relays 1 and 2 respectively. Codes can be between 4-8 digits in length.

This variation comes with a matt 316 stainless steel finish.

Features:

• Module Size: One Module
• Backlit Key Buttons (blue): 1 - 9, ENTER (ARROW), 0 and CLEAR (X)
• 1000 Codes, 2 Relays
• Matt 316 Stainless Steel Finish
• Modules are compatible with both surface and flush 4000 series back boxes
• Can operate as standalone keypad, also networkable via RS485
• User friendly programming menu with audible reassurance tones

Technical Specifications:

• Modular 4000 Series
• Indication LEDs & Reassurance Tones: green LED = data, red LED = prog. & status indication with acoustic signalling during operation and programming
• Access Codes, Relays & Relay Times: Up to 1000 programmable 4 - 8 digit access codes, each code can be set to activate RLY1, RLY2 or both. Each relay can be programmed to operate between 01 to 255 seconds or 00 to work in a latch mode
• Programming Method: Programming carried out via key buttons or using VNET LITE PC software (PC software via RS485 bus connection or micro USB connection)
• Operating Modes: Two modes: Standard mode as standalone codelock or VNET LITE network with RS485 bus; Network mode as serial codelock unit connected via RS485 bus to a remote relay unit 1050 or 1052 with other 4902 keypads
• RS485 BUS & USB Connection: RS485 BUS connection: A and B, for network connection with 1050 or 1052 with other 4902 keypads, also used for programming via PC software. Micro USB port: alternative method of programming via PC software
• RS485 or USB Interface Switch: To select betwen RS485 bus or USB connection: move switch to the upper position for USB selection, move switch to lower position for RS485 bus conneciton
• RS485 Termination: RS485 BUS termination jumper JP1 (JP1 left pos. = termination ON, JP1 right pos. = termination OFF)
• Relay Contacts: 2 Dry Contact Relays: RLY1 = C1/NO1/NC1, RLY2 = C2/NO2/NC2
• Relay Voltage / Amps: Dry Contact Voltage/Current Rating: 24Vac/dc 3A max.
• Back EMF Protection: 2 x selectable MOV jumpers to enable/disable back EMF protection, JP2 and JP3, one per relay
• PTE Inputs: 2 x switched 0V inputs (push-to-make), SW1 (for RLY1) and SW2 (for RLY2)
• Working Voltage: 12-24Vac or dc (compatible with PSUs 321, 322 and HRD-15-12
• Power Consumption: 30mA (max.)
• Working Temperature (C): -10 to +50

Dimensions:

• 103 x 120 x 30 (wld mm)